Step-by-Step Guide: Installing Advanced Sims Golf Simulator Foam Panels Using Contact Adhesive

Installing Advanced Sims Golf Simulator Foam Panels is a straightforward process that can significantly enhance the protection and acoustics of your simulator room. Follow these detailed steps to achieve a professional and secure installation on both walls and ceilings using our recommended contact adhesive.

Materials You Will Need:

  • Advanced Sims Golf Simulator Foam Panels
  • Advanced Sims Contact Adhesive
  • Measuring tape
  • Pencil or chalk
  • Level (for precise alignment)
  • Utility knife (for trimming panels if necessary)
  • Clean cloths or sponges
  • Protective gloves
  • Drop cloths or old sheets (to protect floors and furniture during installation)
  • Step ladder (for ceiling installation)

Step 1: Prepare Your Space

  1. Clear the Area: Remove any furniture or obstructions from the area where you will be installing the panels. Lay down drop cloths to protect the floor.
  2. Clean the Surface: Ensure the walls and ceiling are clean, dry, and free of dust or grease. Use a damp cloth to wipe down surfaces if necessary and allow them to dry completely.
  3. Mark the Layout: Using a measuring tape, level, and pencil or chalk, mark the positions where you will place each panel. Start from the screen end of the wall or ceiling and work your way out to ensure a balanced and even layout.

Step 2: Apply the Contact Adhesive

  1. Prepare the Adhesive: Follow the manufacturer’s instructions for preparing the contact adhesive. Ensure the spray adhesive is well-shaken and ready to apply.
  2. Apply Adhesive to the Panels: Apply an even layer of contact adhesive to the back of the first foam panel. Make sure to cover the entire surface, especially the edges, for a secure bond. Apply the adhesive to a few panels at a time to allow for proper drying time.
  3. Apply Adhesive to the Surface: Similarly, apply an even layer of contact adhesive to the corresponding section of the wall or ceiling. Again, ensure thorough coverage.

Step 3: Mount the Panels

  1. Allow Adhesive to Dry Slightly: Wait for the adhesive on both the panel and the surface to become tacky. This typically takes around 30-60 seconds.
  2. Position the Panel: Carefully align the first panel with your marked layout. Starting from one edge, press the panel firmly against the wall or ceiling, applying even pressure across the surface.
  3. Secure the Panel: Use your hands to press and smooth the panel from the centre outward to eliminate any air bubbles and ensure a strong bond. Pay extra attention to the edges to ensure they are well adhered.

Step 4: Continue Installation

  1. Repeat the Process: Continue applying contact adhesive to the next panel and the corresponding wall or ceiling section. Align each panel carefully with the previous one to maintain a seamless look.
  2. Trim Panels as Needed: If you need to fit panels into corners or around obstacles, use a utility knife or foam cutting tool to trim them to size. Measure carefully and cut slowly for precision.
  3. Install on Ceilings: For ceiling installations, it might be helpful to have an extra pair of hands to hold the panel in place while you press it firmly against the surface. Use a step ladder for safe access.

Step 5: Finishing Touches

  1. Inspect the Installation: Once all panels are installed, inspect the entire surface to ensure all panels are securely adhered and aligned. Make any necessary adjustments or press down any loose edges.
  2. Clean Up: Clean up your workspace and remove any protective coverings from the floor and furniture.

Step 6: Allow Adhesive to Set

  1. Cure Time: Allow the adhesive to fully cure as per the manufacturer’s instructions before using the simulator room. This ensures maximum adhesion and durability of the panels.

Tips for a Successful Installation:

  • Work in a Ventilated Area: Ensure good ventilation while working with adhesive to avoid inhaling fumes.
  • Take Breaks: If installing a large number of panels, take breaks to avoid fatigue and ensure precision.
  • Wear Protective Gear: Use gloves and consider wearing safety glasses to protect against adhesive and sharp tools.

By following these steps, you can achieve a professional and effective installation of your Advanced Sims Golf Simulator Foam Panels. Enjoy the enhanced protection and acoustic benefits they bring to your simulator room! If you have any questions or need assistance, don’t hesitate to contact our support team.

Back to blog